Mixer is a construction equipment used very much in the construction, but in the work, the concrete mixer often occurs the phenomenon of concrete solidification in the mixer, once this situation occurs, it will affect the normal operation of the concrete mixer to a large extent. How to deal with the concreting of the mixer? This is a problem that many construction parties want to know.

　　中科聚峰搅拌机建议指出：混凝土凝结在搅拌机罐里面的缘由有很多，除了没有及时清洗外，其中更主要的原因是搅拌机发动机不能运作，由于没有动力输入液压机而招致液压机中止工作，使得装料罐不能转动而让混凝土凝结在搅拌机罐里面。

　　Zhongke Jufeng mixer suggests that: there are many reasons for the concrete to coagulate in the mixer tank. In addition to not cleaning in time, the main reason is that the mixer engine can't operate. Because there is no power input hydraulic press, the hydraulic press stops working, so that the charging tank can't rotate and the concrete can coagulate in the mixer tank.

　　搅拌机的混凝土凝固了怎么处理？现在给大家介绍两种方法：

　　How to deal with the concreting of the mixer? Here are two solutions:

　　方法一：风炮

　　Method 1: air cannon

　　如果搅拌机内的混凝土已经凝固，建议可以用“风炮”打碎已经凝结的混凝土，然后一点点铲出来！通常罐体下部要割开一个口，然后加翻开一个原来就有用罗丝上紧的封盖，这个盖是让有需求进去工作时翻开通风和紧急情况放料的。在打罐过程中人在罐里面要通风，在装料罐入口应放台风扇吹风进去，而“风炮”工作时会起灰尘，又要接上水管淋湿打碎的混凝土。把罐里面的混凝土打碎铲出以后再把割开部分焊接上，上回封盖，装满水试下转动能否正常，然后少量装料递增看液压机工作能否正常，如果一切正常则表示可以继续运作了。
                                                        

　　If the concrete in the mixer has set, it is recommended to use the "air cannon" to break the concrete already set, and then shovel it out a little bit! Usually, the lower part of the tank body needs to be cut open, and then a cover tightened with a compass is added. This cover is used to open the air and discharge materials in case of emergency. In the process of pouring, people need to ventilate inside the tank. A fan should be placed at the entrance of the charging tank to blow in. When the "air cannon" works, it will generate dust, and it is necessary to connect the water pipe to wet and smash the concrete. After the concrete in the tank is broken and shoveled out, the cut part shall be welded, the cover shall be closed up and filled with water to test whether the rotation can be normal, and then a small amount of loading shall be increased to see whether the hydraulic press can work normally. If everything is normal, it means that it can continue to operate.

　　方法二：电焊或气割

　　Method 2: electric welding or gas cutting

　　混凝土凝固后，其主要成分是硅酸二钙、硅酸三钙。理论上讲，盐酸可以与之反应解除其固态形状。由于搅拌机的料口很小，盐酸量难以控制，且盐酸也可以与搅拌机罐体发生反应，所以操作很难实现。实践中一旦出现这种情况，往往需要用电焊或气割切开罐体，然后将凝固的混凝土机械破碎。

　　After concrete solidification, its main components are dicalcium silicate and tricalcium silicate. In theory, hydrochloric acid can react with it to remove its solid shape. Because the mixer's mouth is very small, the amount of hydrochloric acid is difficult to control, and hydrochloric acid can also react with the mixer tank, so the operation is difficult to achieve. Once this happens in practice, it is often necessary to cut the tank with electric welding or gas cutting, and then the solidified concrete will be mechanically broken.

　　混凝土结块或者凝固在罐体内，会对搅拌机造成很大的伤害，搅拌机的混凝土凝固了怎么处理？通过以上介绍，相信广大用户对这个问题已经有所了解。如果您还想继续了解其相关常识，可以访问中科聚峰搅拌机https://www.jfjiaobanche.com网站详细了解，欢迎网站留言。

　　Concrete caking or solidification in the tank will cause great damage to the mixer. How to deal with the concrete solidification of the mixer? Through the above introduction, I believe that the majority of users have understood this problem. If you want to know more about it, you can visit Zhongke Jufeng mixer https://www.jfjiaobanche.com Official website for more information, welcome to leave a message.