全自动搅拌车开工干活要注重什么事项
1、检查、发现问题并排除故障
1. Check, identify problems, and troubleshoot
全自动搅拌车怕跑在路上，罐子不转了，一般来说装满混凝土的罐子一般停管不能超过2小时，C40级以上的混凝土罐子就一直不能停。
The fully automatic mixer truck is afraid of running on the road and the tank won't rotate. Generally speaking, the tank filled with concrete can't be stopped for more than 2 hours, and concrete tanks above C40 level cannot be stopped for a long time.
卡车启动后，让搅拌罐低速转动，检查胎压，看是否有漏气的轮胎，检查轮胎内是否有石块、钉子等东西卡在里面，并及时清理干净。
After the truck starts, let the mixing tank rotate at low speed, check the tire pressure, see if there are any leaking tires, check if there are stones, nails, and other things stuck inside the tires, and clean them in a timely manner.
全自动搅拌车厂家提醒您要检查侧灯，确保照在轮胎边缘，因为施工现场经常会有钢筋等杂物随意堆积，胎侧薄弱。
The manufacturer of the fully automatic mixing truck reminds you to check the side lights to ensure that they are shining on the edge of the tires, as there are often steel bars and other debris piled up randomly at the construction site, resulting in weak tire sides.
2、确保水箱中有足够的水和减水剂
2. Ensure that there is sufficient water and water reducing agent in the water tank
由于各种原因，当材料过于干燥，不加水无法排出时，减水剂是一种救命稻草，可以保证混凝土的流动性。
Due to various reasons, when the material is too dry and cannot be discharged without adding water, water reducing agents are a life-saving straw that can ensure the fluidity of concrete.
3、确认搅拌罐处于停止状态
3. Confirm that the mixing tank is in a stopped state
因为全自动搅拌车发动机启动时，万一搅拌罐高速旋转，瞬时受力会很大，会对减速器和泵电机系统造成伤害。
Because when the engine of the fully automatic mixing truck starts, if the mixing tank rotates at high speed, the instantaneous force will be very large, which will cause damage to the reducer and pump motor system.
1. 锁定驾驶室内防逆转手柄，以防载物排在道上。
1. Lock the anti reverse handle inside the driver's cab to prevent loads from lining up on the road.
2. 将定位手柄卡入定位卡盘内，锁止机构卡住伸缩总成，固定滑料槽。
2. Insert the positioning handle into the positioning chuck, lock the telescopic assembly with the locking mechanism, and fix the sliding groove.
3.车尾操作手柄应置于“搅动”档内；油门置于怠速位置。
3. The rear operating handle should be placed in the "stirring" position; Place the throttle in the idle position.
4.车辆在行驶过程中，关闭为水箱供气的气源阀门，以免影响车辆的制动性。
4. During driving, close the air supply valve for the water tank to avoid affecting the braking performance of the vehicle.
5.运行时，加长滑料槽必须翻转卸下，放置在挡泥板的专用位置并锁定。以防摆动伤人或影响其它车辆的运行。
5. During operation, the extended sliding chute must be overturned and removed, placed in a dedicated position on the mudguard and locked. To prevent swinging from injuring people or affecting the operation of other vehicles.
6.全自动搅拌车穿越桥、洞、库等设施时，必须要注意通过高度的尺寸，以免发生碰撞造成伤害。
When fully automatic mixer trucks pass through facilities such as bridges, tunnels, and warehouses, attention must be paid to the size of the passing height to avoid collisions and injuries.
全自动搅拌车开工干活要注重的事项就讲解到这里了，希望能够给您好的帮助，更多事项就来我们网站https://www.jfjiaobanche.com咨询！
That's all we need to pay attention to when starting work on a fully automatic mixer truck. We hope it can be helpful to you. For more details, please visit our website https://www.jfjiaobanche.com consulting service
