使用自动上料搅拌车的几个要点
装料时注意清洁
Pay attention to cleanliness during loading
1、装料前先将搅拌筒反转
1. Reverse the mixing drum before loading
自上料搅拌车一般露天停放，装料前先将罐里的积水和树叶之类的杂物排出，以免影响混凝土质量。
The self loading mixer truck is usually parked outdoors. Before loading, the accumulated water and debris such as leaves in the tank should be discharged to avoid affecting the quality of the concrete.
2、装完料要记得冲洗进料斗
2. Remember to flush the feed hopper after loading
洗完后要关掉水箱进气口，打开水箱排气口排掉气体，因为气压下，水管连接不好的地方，容易渗水，影响其他车辆的。再次检查轮胎是否卡有石子铁钉等杂物，使用工具及时清理，因为停车时轮胎与地面接触的地方是检查不到的。
After washing, it is necessary to turn off the air inlet of the water tank and open the air outlet of the water tank to exhaust the gas. This is because under pressure, areas where the water pipe is not properly connected can easily leak water, affecting the safety of other vehicles. Check the tires again for debris such as stones and nails, and use tools to clean them in a timely manner, as the area where the tires come into contact with the ground during parking cannot be detected.
自上料搅拌车厂家提醒您，进入工地时注意观察
The manufacturer of the self loading mixer truck reminds you to pay attention to observation when entering the construction site
1、搅拌车进工地时行驶在路中间
1. The mixing truck is driving in the middle of the road when entering the construction site
一般工地道路简易，路基比较松软，靠近路边，容易被压塌方了，导致车辆侧翻。
Generally, the roads on construction sites are simple, and the roadbed is relatively soft. Near the roadside, it is easy to collapse and cause vehicles to roll over.
2、提前下车查看倒车线路
2. Get off the car in advance and check the reversing route
工地一般工况复杂，倒车时下车绕车一周，查看倒车路线，注意躲避障碍物和坑洼，清理遇到的钢筋钉子。
The general working conditions of the construction site are complex. When reversing, get off the car and take a detour around the car. Check the reversing route, pay attention to avoiding obstacles and potholes, and clean up any steel nails encountered.
3、倒车要慢
3. Reverse slowly
别总是把头伸出窗外，要看着两边后视镜一起兼顾，实在不确定就停车看清楚再倒。用一档起步倒车，缓慢而匀速的行驶，好多路面是挖掘机刚刚铺的比较软，车容易陷入。
Don't always stick your head out of the window. Look at both rearview mirrors and consider them together. If you're unsure, stop and look clearly before reversing. Starting from first gear and reversing at a slow and uniform speed, many roads have just been paved with soft excavators, making it easy for the car to get stuck.
出料时须当心
Be careful when discharging
1、卸料前让自上料搅拌车全速运转几分钟
1. Allow the self loading mixer truck to run at full speed for a few minutes before unloading
高速转动让混凝土充分搅拌，防止凝固，可以加一些水，方面出料。
High speed rotation allows the concrete to be fully mixed to prevent solidification, and some water can be added to discharge the material.
2、出料前先把出料斗溜槽打湿
2. Wet the chute of the discharge hopper before discharging
尽量将车停在平地上出料，出料前先把出料溜槽打湿，防止混凝土粘结在溜槽，容易清洗。
Try to park the vehicle on a flat surface for discharge, and wet the discharge chute before discharge to prevent concrete from sticking to the chute, which is easy to clean.
3、卸料不要大意
3. Don't be careless when unloading
出料时全程看着，免得放料工乱操作放料操作杆，每次罐子正反转中间位子时好停一下，保护减速机，托盘。
When discharging, keep an eye on the entire process to prevent the discharge worker from operating the discharge lever recklessly. Every time the can is rotated in the middle position, it is easy to stop and protect the reducer and tray.
4、自上料搅拌车冲洗干净
4. Flush the self feeding mixer truck thoroughly
自上料搅拌车一定要仔细的冲洗干净，多次反复正转反转罐体，使水无死角清理，多次加水清洗，保持罐体内部的清洁，无混凝土残留。
The self feeding mixer truck must be carefully washed clean, repeatedly rotating and reversing the tank body to ensure that there are no dead corners in the water for cleaning, and repeatedly adding water for cleaning to keep the inside of the tank clean and free of concrete residue.
以上就是小编总结的自上料搅拌车使用时的注意事项，请大家在使用时遵循规章制度，生产。更多相关事项就来我们网站https://www.jfjiaobanche.com咨询！
The above is the summary by the editor of the precautions for using self feeding mixer trucks. Please follow the rules and regulations during use and ensure safe production. For more related matters, come to our website https://www.jfjiaobanche.com consulting service
下一篇：自上料搅拌车搅拌轴停止转动的原因上一篇：自上料搅拌车厂家气压不足怎么？
