搅拌车备用油管使用方法的具体步骤
搅拌车液压油管工作原理是通过搅拌车底盘上的取力器，将发动机的动力传递给液压油泵，产生高压液压油。高压液压油驱动液压马达高速旋转，经减速机产生很大的转矩，驱动搅拌筒转动。利用螺旋传递原理，搅拌筒内置的叶片不断的对混凝土进行强制搅拌，不于出现混凝土凝结的现象。
The working principle of the hydraulic oil pipe of the mixer truck is to transmit the power of the engine to the hydraulic oil pump through the power take-off on the chassis of the mixer truck to generate high-pressure hydraulic oil. The high-pressure hydraulic oil drives the hydraulic motor to rotate at a high speed, and a large torque is generated by the reducer to drive the mixing drum to rotate. Based on the principle of screw transmission, the blades built in the mixing drum continuously force the concrete to mix, so as not to cause the concrete to set.
下面自上料搅拌车厂家再来讲讲搅拌车备用油管使用方法的具体步骤：
Next, let's talk about the specific steps of using the spare oil pipe of the mixer truck from the manufacturer of the charging mixer truck:
⑴ 准备工作准备好三根紧急驱动软管，卸下接管和接头盖。
⑴ preparation prepare three emergency drive hoses, and remove the connecting pipe and connector cover.
⑵ 故障车(被驱动车)的操作
(2) operation of fault vehicle (driven vehicle)
① 将故障车的发动机熄火;
① Shut down the engine of the faulty vehicle;
② 将紧固螺母(左右各有一个)朝左旋松;
② Unscrew the fastening nut (one on the left and one on the right) to the left;
③ 再将旋钮朝右旋转，直到不能再旋为止;
③ Then rotate the knob to the right until it can no longer be rotated;
④ 将高压软管从马达接头处卸下;
④ Remove the high-pressure hose from the motor connector;
⑤ 将紧急驱动软管接到马达接头上;
⑤ Connect the emergency drive hose to the motor connector;
⑥ 把紧急驱动软管上的接管与故障车卸下的高压软管相接，以防漏油。
⑥ Connect the connecting pipe on the emergency drive hose with the high-pressure hose removed by the faulty vehicle to prevent oil leakage.
⑶ 搅拌车(驱动车)的操作
(3) operation of mixer truck (drive truck)
① 将操作手柄于空档位置;
① Set the operating handle to the neutral position;
② 将发动机熄火;
② Shut down the engine;
⑶ 搅拌车(驱动车)的操作
(3) operation of mixer truck (drive truck)
① 将操作手柄于空档位置;
① Set the operating handle to the neutral position;
② 将发动机熄火;
② Stop the engine;
③ 将高压软管从高压油管处卸下;
③ Remove the high-pressure hose from the high-pressure oil pipe;
④ 将紧急驱动软管接到高压油管上;
④ Connect the emergency drive hose to the high-pressure oil pipe;
⑤ 用紧急驱动软管上的接头盖将驱动车的高压软管盖起，以防漏油。
⑤ Cover the high-pressure hose of the drive vehicle with the connector cover on the emergency drive hose to prevent oil leakage.
⑷ 启动搅拌车的发动机。
(4) start the engine of the mixer truck.
⑸ 将搅拌车的操作手柄拨“出料”位置，使故障车内的混凝土排出。
(5) turn the operating handle of the mixer truck to the "discharge" position to discharge the concrete in the faulty truck.
⑹ 紧急驱动完毕后，使两车各自恢复原状。
(6) after the emergency drive is completed, the two vehicles shall be restored to the original state.
搅拌车上装液压油管的连接办法：发动机输出的动力经过取力器转接到液压油泵，液压油泵配有两根油管，一根连接液压油箱，一个连接液压换向阀（两根油管粗细不同），换向阀是四口的，其中两口连接液压马达，另一口连接液压油散热器的出油口，连接就完成了。更多注意事项就来我们网站https://www.jfjiaobanche.com咨询了解吧。
Connection method for installing hydraulic oil pipes on the mixer: the power output from the engine is transferred to the hydraulic oil pump through the power takeoff. The hydraulic oil pump is equipped with two oil pipes, one is connected to the hydraulic oil tank and the other is connected to the hydraulic reversing valve (the two oil pipes are different in thickness). The reversing valve has four ports, two of which are connected to the hydraulic motor and the other is connected to the oil outlet of the hydraulic oil radiator. The connection is completed. Come to our website for more precautions https://www.jfjiaobanche.com Consult and understand.
下一篇：搅拌车进口减速机知识讲解上一篇：全自动搅拌车几大问题解答
