中科聚峰

自上料搅拌车行业持续领跑者!

品质创造未来,让世界爱上中科聚峰造

全国咨询热线
400-879-1999

产品推荐

0.5方自上料搅拌机
0.5方自上料搅拌机
产品介绍:
1.2方自上料搅拌机
1.2方自上料搅拌机
产品介绍:产品型号:JBC-1...
1.8方自上料搅拌机
1.8方自上料搅拌机
产品介绍:参数说明轴距:2...
2.6方自上料搅拌机
2.6方自上料搅拌机
产品介绍:参数说明轴距:2...
2.6同步旋转自上料搅拌机
2.6同步旋转自上料搅拌机
产品介绍:参数说明轴距:2...
2方后置驾驶室自上料搅拌机
2方后置驾驶室自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方D款自上料搅拌机
3.5方D款自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方C款自上料搅拌机
3.5方C款自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方B款自上料搅拌机
3.5方B款自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方A款自上料搅拌机
3.5方A款自上料搅拌机
产品介绍:参数说明轴距:2...
4.0方自上料搅拌机
4.0方自上料搅拌机
产品介绍:参数说明轴距:2...
4方同步旋转自上料搅拌机
4方同步旋转自上料搅拌机
产品介绍:参数说明轴距:3...
5.5方自上料搅拌机
5.5方自上料搅拌机
产品介绍:参数说明轴距:3...
6.5方自上料搅拌机
6.5方自上料搅拌机
产品介绍:参数说明轴距:2...

资讯推荐

当前位置:首页 »中科搅拌机新闻 » 常见问题 » 混凝土搅拌车卸料时的注意事项!

混凝土搅拌车卸料时的注意事项!

来源:https://www.jfjiaobanche.com 浏览:发表时间:2020-12-15
  中科聚峰搅拌车卸料环节其实对于工程的建设进程是很重要的,卸料慢的话会浪费很多的时间,像一般卸料慢的大部分都是小型搅拌车,那只是因为它放量小才卸料慢吗?当然不是,搅拌车卸料慢跟液压泵和液压马达有关,一般小型搅拌车的液压马达都是定量齿轮泵,它的工作速度不怎么快,就是加油门也不会有明显改善,而且还不能长时间的加大油门会烧坏齿轮油泵。下面我们就来了解一下混凝土搅拌车卸料注意事项。
  In fact, the unloading link of concrete mixer truck is very important for the construction process of the project. If the unloading speed is slow, it will waste a lot of time. For example, most of the slow unloading parts are small-sized mixer trucks. Is it only because of its small volume that the unloading is slow? Of course, it is related to the hydraulic pump and hydraulic motor. Generally, the hydraulic motor of small mixer truck is fixed displacement gear pump, Its working speed is not very fast, even if the fuel door will not be significantly improved, and also can not increase the throttle for a long time, it will burn the gear oil pump. Next, we will learn about the concrete mixer truck unloading precautions.
  1、卸料前让搅拌罐全速运转一两分钟。让混凝土充分搅拌,必要时可以加一些水,让混凝土搅拌得更均匀,也方便卸料。
  1. Let the mixing tank run at full speed for one or two minutes before discharging. The concrete can be fully mixed, and some water can be added if necessary to make the concrete more uniform and convenient for unloading.
  2、放料前先把出料斗溜槽打湿。放料时把车尽量停在平地上放料前先把出料斗溜槽打湿,方便清洗。
  2. Wet the discharge hopper chute before discharging. When discharging, park the truck on the flat ground as far as possible. Before discharging, wet the discharge hopper chute to facilitate cleaning.
  3、卸料不要大意和放料工打好关系。放料时尽量自己看着,免得放料工乱操作放料操作杆,每次罐子正反转中间位子时要停一下,保护减速机,托轮等。与放料工打好关系,卸料时也不要睡的太熟,万一工人闹情绪,把你车子放到工地不转罐子,造成闷罐就麻烦了。
  3. Don't be careless in discharging materials and have a good relationship with the discharging workers. When discharging materials, try to watch by yourself, so as to prevent the discharging workers from operating the discharging operating rod disorderly. Stop every time the middle position of the tank is in the forward and reverse direction, so as to protect the reducer and supporting wheel. Make a good relationship with the discharging workers, and don't sleep too well when unloading. In case that the workers are in a mood and put your car on the construction site without turning the cans, it will be troublesome for the cans to be stuffy.
                 中科聚峰搅拌车
  4、搅拌罐一定要仔细地冲洗干净。洗罐子时一定要仔细的冲洗干净,并把水反复的正反转两次,再放出来,然后一趟时把水箱的水全部放进罐子,再回到站加水清洗罐子。
  4. The mixing tank must be washed carefully. When washing the tank, be sure to wash it carefully, and turn the water forward and backward twice, and then put it out again. Then put all the water in the tank into the tank, and then return to the station to clean the tank with water.
  5、之后别忘了施工单位签字。把到工地时间和自己的大名签上,别忘了施工单位签字,否则白干了。
  5. After that, don't forget to sign by the construction unit. Sign the time of arriving at the construction site and your name. Don't forget to sign by the construction unit, otherwise it will be in vain.
  6、在施工现场卸料完毕后,应立即用搅拌车随带的软管冲洗进料斗、出料斗、卸料溜槽等处,清除粘附在车身各处的污泥及混凝土。在返回搅拌站的途中,应向搅拌筒内注150---200L水以清洗筒壁及叶片粘结的混凝土残渣。
  6. After unloading at the construction site, the inlet hopper, discharge hopper and discharge chute should be flushed with the hose attached to the mixer to remove the sludge and concrete adhering to the vehicle body. On the way back to the mixing station, 150-200l water should be injected into the mixing drum to clean the concrete residue bonded by the cylinder wall and blades.
  7、每天工作结束后,司机应负责向搅拌筒内注入清水并高速(14—18转/分)旋转5—10分钟,然后将水排去,以保证筒内清洁。用高压水清洗搅拌筒各个部分时,应注意避开仪表及操纵杆等部位。压力水喷嘴与车身油漆表面间的距离不得小于40厘米。
  7. At the end of each day's work, the driver should inject fresh water into the mixing drum and rotate it at high speed (14-18 RPM) for 5-10 minutes, and then drain the water to ensure the cleanness of the drum. When cleaning each part of the mixing drum with high pressure water, pay attention to avoid the instrument and control rod. The distance between the pressure water nozzle and the paint surface of the vehicle body shall not be less than 40 cm.