自上料搅拌车厂家直销

品质创造未来,爱上中科聚峰造

全国咨询热线
400-879-1999
当前位置:首页 »新闻中心 » 公司新闻关于搅拌车的轴承制作工艺

关于搅拌车的轴承制作工艺

来源:https://www.jfjiaobanche.com 浏览:0发表时间:2022-11-30
目前市场上的混凝土自上料搅拌车需求量很大,购买的人也很多,其制作工艺也是非常关键的,那么关于搅拌车的轴承制作工艺你了解多少呢?下面混凝土自上料搅拌车厂家来介绍。
At present, there is a large demand for concrete self loading mixers in the market, and many people buy them. The manufacturing process is also very critical. How much do you know about the manufacturing process of the bearings of mixers? The concrete below is introduced from the manufacturer of the loading mixer.
搅拌车轴承的设计和制作工艺,须要考虑到轴承的热平衡以控制温升,因为轴承在摩擦状态下工作,由于润滑液体内部摩擦而造成功耗,转化成热量后引起轴承温升。
The design and manufacturing process of the bearing of the mixer truck must take into account the thermal balance of the bearing to control the temperature rise. Because the bearing works under the friction state, the power consumption caused by the internal friction of the lubricating liquid will be converted into heat and cause the bearing temperature rise.
润滑油粘度降低、间隙会改变,会使轴承的巴氏合金软化,严重时产生“烧瓦抱轴”的事故,搅拌车提高轴承的维修和装配质量,保证轴承背面光滑点。
The viscosity of the lubricating oil decreases and the clearance will change, which will soften the babbitt of the bearing. In serious cases, the accident of "bearing burning and shaft seizure" will occur. The mixer improves the maintenance and assembly quality of the bearing, and ensures that the back of the bearing is smooth and spotless.
混凝土自上料搅拌车厂家
定位凸点完整无损,自身的弹开量为0.5-1.5mm,这保证装配后轴瓦借助自身弹力与轴承座孔贴合紧密,转载轴承座内的上下两片轴瓦的每端均应高出轴承座平面30-50微米,高出量可保证按规定扭矩拧紧轴承盖螺栓后轴承与轴承座紧密配合,产生足够的摩擦自锁力。
The locating bump is intact, and its own springing off is 0.5-1.5mm, which ensures that the bearing pad fits closely with the bearing seat hole with its own elasticity after assembly. Each end of the upper and lower bearing pads in the transfer bearing seat shall be 30-50 microns higher than the bearing seat plane, and the amount of springing off can ensure that the bearing fits closely with the bearing seat after tightening the bearing cover bolts according to the specified torque, generating sufficient friction self-locking force.
轴承不致松动,散热效果好,防止轴承烧蚀和磨损,轴承的工作面不能用刮配法达到75%-85%接触印痕做衡量标准,应在不刮削时就使轴承和轴径的配合间隙达到要求。
The bearing is not loose, and the heat dissipation effect is good to prevent bearing ablation and wear. The working surface of the bearing cannot be measured by scraping to 75% - 85% of the contact mark. The fit clearance between the bearing and the shaft diameter should meet the requirements without scraping.
搅拌车在使用过程中保养是必不可少的,大家在做保养的时候尽量能够面面俱到,将搅拌车的保养做到很好,更多相关内容了解就来我们网站https://www.jfjiaobanche.com资讯看看吧!
The maintenance of the mixer is essential in the process of use. We should try our best to cover everything when doing maintenance, and do a good job of the maintenance of the mixer. For more information, please come to our website https://www.jfjiaobanche.com Look at the information!