混凝土自上料搅拌车厂家

自上料搅拌车行业持续领跑者!

品质创造未来,让世界爱上中科聚峰造

全国咨询热线
400-879-1999
当前位置:首页 »新闻中心 » 新闻资讯 » 中科搅拌机的零件破损速度怎么控制

中科搅拌机的零件破损速度怎么控制

来源:https://www.jfjiaobanche.com 浏览:发表时间:2020-04-13
  如果你发现搅拌机的部件在使用过程中损坏得非常快,你必须找出具体的原因并解决它。现在让我们来分析一下为什么搅拌器的部件分解得这么快。在中科搅拌机厂家帮大家查明原因之后,你就知道如何解决它了。
  If you find that the parts of the mixer are damaged very quickly in use, you must find out the specific reason and solve it. Now let's analyze why the parts of the stirrer break down so fast. After we find out the reason for it, you will know how to solve it.
  在机器工作怕的是机器零件损坏,不是有价值的一小部分,但影响了工作的进展是更麻烦的事情,尤其是当时间是不够的,那么机器零件损坏将严重影响工作效率,今天小编给你介绍搅拌机配件损坏加快的原因。
  Working in the machine is afraid of the damage of machine parts, not a small part of value, but it is the most troublesome thing to affect the progress of the work, especially when time is not enough, then the damage of machine parts will seriously affect the work efficiency. Today Xiaobian will introduce the reason why the damage of mixer parts accelerates.
中科搅拌机
  搅拌器一般采用叶轮式搅拌器,设备配有辅助吸风口,通过调节板可适当开启。当搅拌机工作时,搅拌后的原料能及时排出。如果调整的开板太小,空气进入房间的数量并不大,混合室的负面压力小,混合材料的放电不是免费的,混合材料太粉,在混合室的热量不能及时排放,搅拌机必然会“发烧”。当搅拌机“发热”时,必须检查调节板的开度。
  Generally, impeller agitator is used for agitator, and the equipment is equipped with auxiliary air suction port, which can be opened properly through regulating plate. When the mixer is working, the raw materials after mixing can be discharged in time. If the adjusted opening plate is too small, the amount of air entering the room is not large, the negative pressure in the mixing room is small, the discharge of the mixed material is not free, the mixed material is too powdery, the heat in the mixing room cannot be discharged in time, and the mixer will inevitably have a "fever". When the mixer is "hot", the opening of the regulating plate must be checked.
  搅拌物料沉降室的空间要尽可能的大,这是道路畅通的保证,有利于搅拌物料的顺利及时排出。因此在设计中应预留以满足工艺要求。高速混合机锤击,摩擦材料,材料中的水分和细粉尘将脉冲集尘袋袋粘连,风的阻力增加,随着时间的增长,集尘袋风量和空气压力损失,严重时使轧机“发烧”,减少生产,必须及时更换或清洗集尘袋袋。
  The space of the mixing material settling chamber shall be as large as possible, which is the guarantee of smooth road and is conducive to the smooth and timely discharge of the mixing material. Therefore, it should be reserved in the design to meet the process requirements. High speed mixer hammering, friction materials, moisture and fine dust in the materials will stick the pulse dust collection bag, and the resistance of the wind will increase. With the increase of time, the air volume and air pressure of the dust collection bag will be lost. In serious cases, the mill will have "fever" and production will be reduced. The dust collection bag must be replaced or cleaned in time.
  搅拌机使用不当,长期处于超负荷工作状态,还会引起搅拌机发热,甚至烧坏电机。良好的工作状态是电机在90%的额定负载下工作。在正确分析机器磨损的原因后,我们可以积较地纠正机器正确的使用方式和正确的电压。
  Improper use of the mixer, long-term overload working state, will cause mixer heating, or even burn out the motor. Good working condition is that the motor works under 90% of rated load. After correctly analyzing the causes of machine wear, we can actively correct the correct use of the machine and the correct voltage.
  这些都是可能导致搅拌机零件破碎速度的具体原因。我希望你把上面的问题讲清楚后,能注意一下。
  These are the specific reasons that may cause the crushing speed of mixer parts. I hope you can pay attention to the above questions after you have made them clear.
  以上是中科搅拌机小编为大家介绍的相关内容,想要了解更多内容,欢迎访问网站:https://www.jfjiaobanche.com
  The above is the relevant content introduced by Zhongke blender. To learn more, please visit the website: https://www.jfjiaobanche.com