中科聚峰

自上料搅拌车行业持续领跑者!

品质创造未来,让世界爱上中科聚峰造

全国咨询热线
400-879-1999

产品推荐

0.5方自上料搅拌机
0.5方自上料搅拌机
产品介绍:
1.2方自上料搅拌机
1.2方自上料搅拌机
产品介绍:产品型号:JBC-1...
1.8方自上料搅拌机
1.8方自上料搅拌机
产品介绍:参数说明轴距:2...
2.6方自上料搅拌机
2.6方自上料搅拌机
产品介绍:参数说明轴距:2...
2.6同步旋转自上料搅拌机
2.6同步旋转自上料搅拌机
产品介绍:参数说明轴距:2...
2方后置驾驶室自上料搅拌机
2方后置驾驶室自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方D款自上料搅拌机
3.5方D款自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方C款自上料搅拌机
3.5方C款自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方B款自上料搅拌机
3.5方B款自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方A款自上料搅拌机
3.5方A款自上料搅拌机
产品介绍:参数说明轴距:2...
4.0方自上料搅拌机
4.0方自上料搅拌机
产品介绍:参数说明轴距:2...
4方同步旋转自上料搅拌机
4方同步旋转自上料搅拌机
产品介绍:参数说明轴距:3...
5.5方自上料搅拌机
5.5方自上料搅拌机
产品介绍:参数说明轴距:3...
6.5方自上料搅拌机
6.5方自上料搅拌机
产品介绍:参数说明轴距:2...

资讯推荐

当前位置:首页 »中科搅拌机新闻 » 新闻资讯 » 如何清理中科搅拌机发动机舱油泥呢?

如何清理中科搅拌机发动机舱油泥呢?

来源:https://www.jfjiaobanche.com 浏览:发表时间:2021-01-09
中科混凝土搅拌机经常行驶在建筑工地上,在发动机的使用过程中,避免不了各种油液的蒸汽生成的油泥,这些油泥和灰尘污垢混杂在一起受热,成为汽车自燃的隐患之一,其次是大量灰尘与湿空气结合后呈泥状附着在发动机的零件与管路上,这会加快零件的老化与损坏;较脏的发动机舱容易成为老鼠及一些爬行动物的窝,所以发动机舱的清洗势在必行。发动机舱该怎么清洗呢?中科混凝土搅拌机教您怎么清洗发动机舱。
Zhongke concrete mixer often runs on the construction site. During the use of the engine, it can not avoid the sludge generated by the steam of all kinds of oil. These sludge and dust are mixed together and heated, which has become one of the hidden dangers of auto spontaneous combustion. Secondly, a large amount of dust and wet air are combined and attached to the engine parts and pipelines in the form of sludge, which will accelerate the aging of parts The dirty engine compartment is easy to become the nest of mice and some reptiles, so it is imperative to clean the engine compartment. How to clean the engine compartment? Zhongke concrete mixer teaches you how to clean the engine compartment.
1. 准备清洗工具,发动机外表清洗剂和发动机线束护理剂;一把小刷子,刷头宽度不要太大,因为发动机舱的缝隙多且狭窄,用窄头更加方便;一个口罩和一双手套,发动机外表清洗剂对人体有一定的危害,味儿有点刺鼻,所以要准备口罩和手套。
1. Prepare cleaning tools, engine surface cleaning agent and engine harness care agent; a small brush, the width of the brush head should not be too large, because there are many and narrow gaps in the engine compartment, it is more convenient to use the narrow head; a mask and a pair of gloves, the engine surface cleaning agent has certain harm to the human body, the smell is a little pungent, so prepare masks and gloves.
2. 找一个停车的位置,发动机的清洗避免不了有污水流到地上,所以在准备清洗之前,尽量将车辆停放到人车稀少之处。
2. Find a parking place, the engine cleaning can not avoid sewage flow to the ground, so before cleaning, try to park the vehicle in the place where there are few people and vehicles.
3. 先将发动机的装饰盖卸掉,先用抹布或者刷子对发动机舱进行简单的除尘,然后就可以用发动机外表清洗剂操作。首先将发动机内部的保险盒、点火线圈、发电机等一些不能沾水和清洗剂的零部件做一下防水处理(这些零部件可以单独清洁),之后将清洗剂摇匀,再喷在发动机舱内的零部件上,注意喷洒距离保持在15厘米左右就可以了,尽量喷洒均匀一些,油泥多的地方适当多喷一些。
3. First remove the decorative cover of the engine. First, simply remove the dust from the engine compartment with a rag or brush, and then use the cleaning agent on the surface of the engine. First of all, waterproof the fuse box, ignition coil, generator and other parts that can't be stained with water and cleaning agent (these parts can be cleaned separately), then shake the cleaning agent evenly, and spray it on the parts in the engine compartment. Pay attention to keep the spraying distance at about 15 cm. Spray it evenly as far as possible, and the place with a lot of oil sludge is appropriate Spray more.
             中科搅拌机
4. 用小刷子清理,在喷完清洗剂后,需等待5分钟左右,让清洗剂继续化解油泥,直至完全化解,然后用小刷子进行刷洗,可以明显看到油泥化开的效果。发动机舱缝隙较多,一定要耐心刷干净,因为之后还会喷上养护剂(相当于上了一层蜡油),如果不刷洗干净,脏东西就封在里面了。自上料搅拌机,发动机的进气管很容易沾上油泥,颜色难看且不易清洗,需要细心的刷干净,还有一些走电、走油液的管路,也要清洗干净,防止油泥和其它污物对它们进行腐蚀,造成泄漏。
4. Clean with a small brush. After spraying the cleaning agent, you need to wait for about 5 minutes to let the cleaning agent continue to dissolve the oil sludge until it is completely dissolved. Then brush with a small brush to see the effect of oil sludge melting. There are many gaps in the engine compartment, so you must brush it patiently, because after that, you will spray the curing agent (equivalent to a layer of wax oil). If you don't brush it clean, the dirty things will be sealed inside. Since the feeding mixer, the intake pipe of the engine is easy to be stained with oil sludge. The color is ugly and difficult to clean. It needs to be cleaned carefully. There are also some power and oil pipelines that need to be cleaned to prevent oil sludge and other dirt from corroding them and causing leakage.
5. 清水清洗,清洗剂在化解油泥后,还是会附着在发动机舱内的各个零件上,所以在它们即将风干之前,需要用清水清洗干净,切忌用高压水枪清洗。自上料搅拌机,在清洗之前先要做一下防范措施,就是先启动发动机保持怠速状态,这样做的原因有两点:一是防止点线圈等关键部位溅到水后,造成短时间启动困难,二是发动机运转后,机体温度会上升,可以加速水蒸发变干。
5. Clean with clean water. After dissolving the oil sludge, the cleaning agent will still adhere to all parts in the engine compartment, so before they are about to dry, they need to be cleaned with clean water, and do not use high-pressure water gun. Before cleaning, the self feeding mixer should take some preventive measures, that is, start the engine to keep idle. There are two reasons for this: one is to prevent the key parts such as the point coil from splashing with water, which makes it difficult to start in a short time; the other is that after the engine is running, the body temperature will rise, which can accelerate the evaporation and drying of water.
6. 线束护理剂,在用水清洗之后,一定要将发动机内部件上的水吹干,气枪吹干是比较好的方式,如果没有,只能用吸水性好的毛巾擦干,然后待其完全晾干。然后将线束护理剂均匀地喷洒在发动机舱内的各个部件上就好了。这样做可以防止油泥积累,减缓线束老化,减少老旧车型自燃的几率。自上料搅拌机价格不算便宜,一定要保养好,让它为您带来更多的经济收益。
6. Harness care agent: after cleaning with water, be sure to blow dry the water on the internal parts of the engine. Air gun blow dry is a better way. If not, you can only dry it with a towel with good water absorption, and then wait for it to dry completely. Then spray the harness care agent evenly on all parts in the engine compartment. This can prevent the accumulation of oil sludge, slow down the aging of wiring harness, and reduce the probability of spontaneous combustion of old models. The price of self feeding mixer is not cheap, so it must be well maintained to bring you more economic benefits.