自上料搅拌车厂家直销

品质创造未来,爱上中科聚峰造

全国咨询热线
400-879-1999
当前位置:首页 »新闻中心 » 行业动态搅拌车更换液压油及齿轮油需注意的事宜

搅拌车更换液压油及齿轮油需注意的事宜

来源:https://www.jfjiaobanche.com 浏览:0发表时间:2023-03-17
搅拌车的保养少不了液压油及齿轮油的定期更换,这是相当关键的,更换过程也需注意,做不好会造成液压件故障、闷罐现象,接下来自上料搅拌车厂家给大家讲讲液压油及齿轮油更换时需注意的事宜吧。
The maintenance of the mixing truck requires regular replacement of hydraulic oil and gear oil, which is quite crucial. Attention should also be paid to the replacement process. Failure to do so can cause hydraulic component failures and tank tightness. Next, let's talk about the matters needing attention when replacing hydraulic oil and gear oil from the manufacturer of the loading mixing truck.
1、加油或换油时,发动机必须处于停止状态,否则将造成液压系统损坏。
1. When refueling or changing oil, the engine must be stopped, otherwise damage to the hydraulic system will occur.
2、每次换油前,必须检查整个系统的密封性能,重新紧固所有的螺栓,必要时更换新的密封元件。
2. Before each oil change, it is necessary to check the sealing performance of the entire system, retighten all bolts, and replace new sealing elements if necessary.
3、禁止不同牌号的液压油、齿轮油混用或使用不合格油品。车辆出厂时使用的油品型号在油箱上的标签和《说明书》上都有显示,初次换油时如果所用油品与出厂时油品型号不同,须清洗液压系统。
3. It is prohibited to mix hydraulic oil and gear oil of different brands or use unqualified oil products. The type of oil used when the vehicle leaves the factory is shown on the label on the fuel tank and in the Manual. If the oil used during the initial oil change is different from the type of oil used when the vehicle leaves the factory, the hydraulic system must be cleaned.
4、更换出的废油,应妥善保存和处理,不能随意倒掉,注意保护环境。
4. The replaced waste oil should be properly stored and disposed of, and should not be arbitrarily dumped. Attention should be paid to protecting the environment.
自上料搅拌车厂家
5、在新换好油品后,让发动机在搅拌筒不转的情况下,空转15分钟,检查油位是否合适。
5. After the new oil is replaced, let the engine idle for 15 minutes without the mixing drum running, and check whether the oil level is appropriate.
此外建议大家在保养时一定要选择原厂纯正的油品和滤芯,保证系统运转正常。齿轮油主要起润滑,冲洗,防锈等作用,减速机在运转过程中,会产生金属磨料,磨料经过沉淀,会被放油堵上的磁铁吸附,当磨料达到一定量后,会混在油中,加速齿轮和轴承磨损;同时,长期不换油,油液的综合性能也会降低,影响减速机的使用寿命。
In addition, it is recommended that you choose genuine oil products and filter elements from the original factory during maintenance to ensure the normal operation of the system. Gear oil is mainly used for lubrication, flushing, rust prevention, and other functions. During the operation of the reducer, metal abrasives will be generated. After precipitation, the abrasives will be absorbed by the magnets on the oil drain plug. When the amount of abrasives reaches a certain amount, they will be mixed in the oil, accelerating the wear of the gears and bearings; At the same time, if the oil is not changed for a long time, the comprehensive performance of the oil will also decrease, affecting the service life of the reducer.
搅拌车更换液压油及齿轮油需注意的事宜就讲解到这里了,您对此有怎样的疑惑或者需求就来我们网站https://www.jfjiaobanche.com咨询了解吧!
That's all we need to pay attention to when replacing hydraulic oil and gear oil on the mixer truck. If you have any doubts or needs about this, please come to our website https://www.jfjiaobanche.com Consult and understand!