全自动搅拌车具备三大核心系统功能
全自动搅拌车工作原理是通过取力装置将汽车底盘的动力取出，并驱动液压系统的变量泵，把机械能转化为液压能传给定量马达，马达再驱动减速机，由减速机驱动搅拌装置，对混凝土进行搅拌。在运送完混凝土后，通常要用水冲洗搅拌筒内部，以防止硬化的混凝土占用搅拌筒空间，使搅拌筒的容积变小。下面全自动搅拌车厂家来讲讲它具备三大核心系统功能。
The working principle of the fully automatic mixer is to take out the power of the vehicle chassis through the power take-off device, drive the variable pump of the hydraulic system, convert the mechanical energy into hydraulic energy, and transmit it to the quantitative motor. The motor drives the reducer, and the reducer drives the mixing device to mix the concrete. After the concrete is transported, it is usually necessary to flush the inside of the mixing drum with water to prevent the hardened concrete from occupying the space of the mixing drum and reducing the volume of the mixing drum. Next, the manufacturer of the fully automatic mixer will tell us that it has three core system functions.
进出料系统
Feeding and discharging system
全自动搅拌车进出料系统由进料斗、出料斗、主卸料槽、副卸料槽、支架、锁紧架等组成，是全自动搅拌车的重要组成部分，直接影响到进出料的速度和质量。进、出料斗通过支架和副车架的后台支撑架相连。
The feeding and discharging system of the fully automatic mixer consists of the feed hopper, the discharge hopper, the main discharge chute, the auxiliary discharge chute, the bracket, the locking frame, etc. It is an important part of the fully automatic mixer, which directly affects the speed and quality of feeding and discharging. The feed hopper and the discharge hopper are connected with the rear support frame of the sub frame through a bracket.
出料斗及主卸料槽内加有衬板，衬板采用高强度细晶粒合金钢，其耐磨能力为Q345A(原16Mn)的1.59倍，大幅度的提高了耐磨性。主卸料槽能使混凝土朝所要求的方向卸出，副卸料槽起延长主卸料槽的长度的作用。
The discharge hopper and main discharge chute are equipped with lining plates. The lining plates are made of high-strength fine grain alloy steel, and their wear resistance is 1.59 times that of Q345A (original 16Mn), greatly improving the wear resistance. The main discharge chute can discharge the concrete in the required direction, and the auxiliary discharge chute can extend the length of the main discharge chute.
在副卸料槽接长时，拉下副卸料槽上的锁柄，锁紧。锁紧架在卸料槽不工作时，将主卸料槽锁定。卸料槽不工作时，将其向里一推，便会自动锁定，掀下锁柄，即可将卸料槽拉出。
When the auxiliary discharge chute is extended, pull down the lock handle on the auxiliary discharge chute and lock it. When the discharge chute does not work, the locking frame locks the main discharge chute. When the discharge chute does not work, push it inward to automatically lock it. Lift the lock handle to pull out the discharge chute.
卸料槽控制杆起回转支撑卸料槽，及调节卸料槽槽口的上下位移的作用，采用螺旋丝杠传动，定位准确，联接可靠，移动时轻巧省力。锁紧杆将转任意一位置的卸料槽锁定。掀下手柄，即可解除锁定。
The control rod of the discharge chute acts as a rotary support for the discharge chute and adjusts the up and down displacement of the discharge chute notch. It is driven by a screw lead screw, with accurate positioning, reliable connection, and light and labor-saving movement. The locking lever will turn to lock the discharge chute in any position. Lift the handle to unlock it.
操作系统
operating system
全自动搅拌车操作系统由控制器、联动轴、软轴及连杆机构组成,主要控制搅拌筒的转速及旋转方向。
The fully automatic mixer operating system consists of a controller, a linkage shaft, a flexible shaft and a linkage mechanism, which mainly controls the speed and direction of rotation of the mixing drum.
全自动搅拌车后部两侧各布置一套控制器，左右控制器可以实现联动，控制器上只有一根操纵杆，接出端分别通过连杆机构连接到变量泵上，通过改变泵上控制柄的角度来调节油泵的流量，从而实现控制筒体转动的方向和速度，通过左右移动手柄来控制。
A set of controllers are arranged at both sides of the rear of the fully automatic mixer truck. The left and right controllers can realize linkage. There is only one control lever on the controller. The outlet end is connected to the variable displacement pump through the linkage mechanism. The flow of the oil pump is adjusted by changing the angle of the control handle on the pump, so as to control the direction and speed of cylinder rotation, which is controlled by moving the handle left and right.
该手柄同时还端通过软轴连到发动机的油门上，在需要加大转速时可上下移动来操纵手柄，控制此操纵杆来实现筒体转速的提高。
At the same time, the handle is also connected to the accelerator of the engine through a flexible shaft. When the speed needs to be increased, it can be moved up and down to control the handle, so as to increase the cylinder speed.
电器系统
Electrical system
全自动搅拌车的电器系统由三部分组成：冷却风扇控制部分和后示廓灯部分。冷却风扇控制部分：冷却风扇的起停由温度开关自动控制，温度高于65℃时风扇启动，低于60℃时风扇停止。
The electrical system of the fully automatic mixer consists of three parts: the cooling fan control part and the rear position lamp part. Cooling fan control part: the start and stop of the cooling fan is automatically controlled by the temperature switch. The fan starts when the temperature is higher than 65 ℃ and stops when the temperature is lower than 60 ℃.
温度开关位于冷却器上，继电器与保险片在蓄电池旁电源继电器盒内。后示廓灯部分：后示廓灯用于夜间表示车后部轮廓大小，与后牌照灯同时点亮与熄灭。
The temperature switch is located on the cooler, and the relay and fuse are located in the power relay box beside the battery. Rear position lamp: the rear position lamp is used to indicate the size of the rear contour at night, and it is turned on and off at the same time as the rear license plate lamp.
全自动搅拌车冬期施工时，应切实做到：开机前检查是否结冰，下班时认真排除拌筒内及供水系统内残存积水。关闭水泵开关，将控制手柄置于“停止”位置。更多相关的注意事项就来我们网站https://www.jfjiaobanche.com进行咨询吧！
During the winter construction of the fully automatic mixer, it shall be ensured that: before starting up, check whether there is ice, and carefully remove the residual water in the mixing drum and water supply system when off duty. Turn off the water pump switch and place the control handle at the "Stop" position. More relevant precautions come to our website https://www.jfjiaobanche.com Consult!
