搅拌车发动机外部清洗的正确打开方式
混凝土搅拌机不缺发动机保养，发动机维护还包括发动机的外部清洁。你认为这就是发动机外部清洁的目的吗？那是个大错误。这是正确的方式打开外部清洗混凝土搅拌机引擎！
The concrete mixer does not lack engine maintenance, which also includes the external cleaning of the engine. Do you think this is the purpose of engine exterior cleaning? That was a big mistake. This is the right way to turn on the external washing concrete mixer engine!
步：用塑料薄膜覆盖搅拌机电器，然后用半湿毛巾覆盖在薄膜的上面，防止高压水冲入分配器，使搅拌机难以启动。
Step 1: cover the mixer with plastic film, and then cover the film with a semi wet towel to prevent high-pressure water from rushing into the distributor, making it difficult to start the mixer.
第二步：用高压水枪从上到下机舱内外附着的污垢。
Step 2: remove the dirt inside and outside the engine room from top to bottom with a high-pressure water gun.
第三步：将混凝土自上料搅拌车外部清洗剂均匀地喷在浸湿的搅拌车和机舱周围。三分钟后，用纤维刷清洁机舱内所有可触及的零件。
Step 3: spray the concrete from the external cleaning agent of the loading mixer evenly around the wetted mixer and the engine room. After three minutes, clean all accessible parts in the engine room with a fiber brush.
第四步：使用高压水枪快速清洁污垢。
Step 4: use a high-pressure water gun to quickly clean dirt.
第五步：将外部清洗剂喷在搅拌车表面，操作步骤同上，直搅拌车表面清洗干净。
Step 5: spray the external cleaning agent on the surface of the mixer. The operation steps are the same as above until the surface of the mixer is cleaned.
第六步：后用半湿毛巾擦干清洗过的搅拌机发动机，用真空吸风机将手难以触及的地方吹干，然后风干。
Step 6: after that, wipe the cleaned mixer engine with a semi wet towel, use a vacuum suction fan to dry the places that are difficult to reach, and then air dry.
第七步：将机舱内的塑料橡胶件用塑料橡胶保护罩打磨，然后将金属件涂上。
Step 7: polish the plastic rubber parts in the engine room with the plastic rubber protective cover, and then coat the metal parts.
第八步：混凝土自上料搅拌车厂家提醒您，护理结束后，后用干净的无纺布抛光巾对发动机和机舱侧面进行检查。
Step 8: the concrete mixer manufacturer reminds you that after the nursing, the engine and cabin sides should be inspected with clean non-woven polishing towels.
此外日常维护并不可少，由于混凝土会在短时间内凝固成硬块，且对钢材和油漆有一定的腐蚀性，所以每次使用混凝土贮罐后，洗净粘附在混凝土贮罐及进出料口上的混凝土是每日维护需认真进行的工作。其中包括：
In addition, routine maintenance is necessary. Since the concrete will solidify into hard blocks in a short time and have certain corrosivity to steel and paint, cleaning the concrete adhered to the concrete storage tank and the inlet and outlet after each use of the concrete storage tank is a daily maintenance work that needs to be carefully carried out. These include:
每次装料前用水冲洗进料口，使进料口在装料时保持湿润；在装料的同时向随车自带的清洗用水水箱中注满水；装料后冲洗进料口，洗净进料口附近残留的混凝土；到工地卸料后，冲洗出料槽，然后向混凝土贮罐内加清洗用水30—40L；在车辆回程时保持混凝土贮罐正向慢速转动；下次装料前切记放掉混凝土贮罐内的污水；每天收工时全部清洗混凝土贮罐及进出料口周围，保证不粘有水泥及混凝土结块。
Wash the inlet with water before each loading to keep the inlet moist during loading; Fill the cleaning water tank with water while loading; Wash the inlet after loading, and clean the residual concrete near the inlet; After unloading at the construction site, wash the discharge tank, and then add 30-40l of cleaning water to the concrete storage tank; Keep the concrete storage tank rotating forward and slowly when the vehicle returns; Remember to discharge the sewage in the concrete storage tank before the next loading; Clean the concrete storage tank and the area around the inlet and outlet at the end of each day to ensure that there is no cement or concrete caking.
以上就是今天为大家分享的关于问题的相关内容，希望对大家能有所帮助，想要了解更多内容可以电话联系我们或者关注我们的网站https://www.jfjiaobanche.com。
The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website https://www.jfjiaobanche.com 。
下一篇：冬天开搅拌机耗油更多原因三个上一篇：混凝土自上料搅拌车调整制动间隙的关键
