中科聚峰

自上料搅拌车行业持续领跑者!

品质创造未来,让世界爱上中科聚峰造

全国咨询热线
400-879-1999

产品推荐

0.5方自上料搅拌机
0.5方自上料搅拌机
产品介绍:
1.2方自上料搅拌机
1.2方自上料搅拌机
产品介绍:产品型号:JBC-1...
1.8方自上料搅拌机
1.8方自上料搅拌机
产品介绍:参数说明轴距:2...
2.6方自上料搅拌机
2.6方自上料搅拌机
产品介绍:参数说明轴距:2...
2.6同步旋转自上料搅拌机
2.6同步旋转自上料搅拌机
产品介绍:参数说明轴距:2...
2方后置驾驶室自上料搅拌机
2方后置驾驶室自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方D款自上料搅拌机
3.5方D款自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方C款自上料搅拌机
3.5方C款自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方B款自上料搅拌机
3.5方B款自上料搅拌机
产品介绍:参数说明轴距:2...
3.5方A款自上料搅拌机
3.5方A款自上料搅拌机
产品介绍:参数说明轴距:2...
4.0方自上料搅拌机
4.0方自上料搅拌机
产品介绍:参数说明轴距:2...
4方同步旋转自上料搅拌机
4方同步旋转自上料搅拌机
产品介绍:参数说明轴距:3...
5.5方自上料搅拌机
5.5方自上料搅拌机
产品介绍:参数说明轴距:3...
6.5方自上料搅拌机
6.5方自上料搅拌机
产品介绍:参数说明轴距:2...

资讯推荐

当前位置:首页 »中科搅拌机新闻 » 行业动态 » 中科搅拌机出现抱轴情况的原因分析!

中科搅拌机出现抱轴情况的原因分析!

来源:https://www.jfjiaobanche.com 浏览:发表时间:2020-10-19
你知道中科搅拌机在工作时为什么会出现抱轴情况吗?因在整个搅拌期间,粉料、砂石、液体混合所形成的粘结物,黏附在搅拌轴、搅拌臂上,经过长时间的积累,机械内部表面就会形成一层厚实且不易清理的粘结物。
Do you know why the shaft holding occurs when the mixer is working? During the whole mixing period, the binder formed by mixing powder, sand and liquid adheres to the mixing shaft and mixing arm. After a long time of accumulation, a thick and hard to clean adhesive will be formed on the internal surface of the machine.
影响混凝土质量,当机械在运行时出现抱轴后,就会打出不均匀的混凝土。
Affect the quality of concrete, when the machine is in operation, the uneven concrete will be produced.
增加机械负载,增加能耗。
Increase mechanical load and energy consumption.
影响耐磨件、轴端密封的使用寿命,加快耐磨件的磨损速度。发生抱轴后,搅拌臂也会磨损得非常严重,使用寿命也会明显缩短。
The service life of wear-resistant parts and shaft end seals is affected, and the wear rate of wear-resistant parts is accelerated. After axle holding, the mixing arm will be seriously worn and its service life will be significantly shortened.
         中科搅拌机
对进料顺序、进料时间进行有效调整,骨料、粉料预混落入主机内(骨料须先下一部分),这样可让粉料在一定程度上附着在骨料上,减轻粉料落入主机内附着在搅拌轴、臂上的可能性降低,并且还可提高搅拌效率。
The feeding sequence and feeding time are effectively adjusted, and the premixed aggregate and powder fall into the host machine (the aggregate must be the next part first), which can make the powder adhere to the aggregate to a certain extent, reduce the possibility of powder falling into the host and adhere to the mixing shaft and arm, and improve the mixing efficiency.
主机盖水管线要求与搅拌轴线处于同一垂直面上,同时还应保证搅拌臂与搅拌轴夹角位置上方有直喷喷嘴。因搅拌臂、轴夹角位置是粘结物容易附着的地方,一般出现抱轴都是从搅拌臂根部开始,同时还要求加水时间贯穿始终。
The center line of the water pipe on the cover of the main engine should be in the same vertical plane as the center line of the mixing shaft. At the same time, it should be ensured that there is a direct injection nozzle above the angle between the mixing arm and the mixing shaft. Because the angle between the mixing arm and the shaft is the place where the adhesive is easy to adhere, the shaft holding usually starts from the root of the mixing arm, and at the same time, it is required to add water through the whole process.
随着工程项目的不断推进,与工程项目密切相关的搅拌设备使用次数也会随之加多,而它作为搅拌设备的“心脏”,提升机械设计、使用科学性具有至关重要的作用。
With the continuous progress of engineering projects, the use of mixing equipment closely related to engineering projects will also increase. As the "heart" of mixing equipment, it plays an important role in improving mechanical design and scientific use.